/**
  ******************************************************************************
  * File Name          : gpio.c
  * Description        : This file provides code for the configuration
  *                      of all used GPIO pins.
  ******************************************************************************
  * @attention
  *
  * <h2><center>&copy; Copyright (c) 2019 STMicroelectronics.
  * All rights reserved.</center></h2>
  *
  * This software component is licensed by ST under BSD 3-Clause license,
  * the "License"; You may not use this file except in compliance with the
  * License. You may obtain a copy of the License at:
  *                        opensource.org/licenses/BSD-3-Clause
  *
  ******************************************************************************
  */

/* Includes ------------------------------------------------------------------*/
#include "gpio.h"
/* USER CODE BEGIN 0 */
#include "ads1260.h"
/* USER CODE END 0 */

/*----------------------------------------------------------------------------*/
/* Configure GPIO                                                             */
/*----------------------------------------------------------------------------*/
/* USER CODE BEGIN 1 */

/* USER CODE END 1 */

/** Configure pins as 
        * Analog 
        * Input 
        * Output
        * EVENT_OUT
        * EXTI
*/
void MX_GPIO_Init(void)
{

  GPIO_InitTypeDef GPIO_InitStruct = {0};

  /* GPIO Ports Clock Enable */
  __HAL_RCC_GPIOB_CLK_ENABLE();
  __HAL_RCC_GPIOC_CLK_ENABLE();
  __HAL_RCC_GPIOF_CLK_ENABLE();
  __HAL_RCC_GPIOA_CLK_ENABLE();

  /*Configure GPIO pin Output Level */
  HAL_GPIO_WritePin(GPIOA, ADC_RESET_Pin|ADC_START_CONV_Pin 
                    #ifndef MCO_TEST_FUNCTION 
                    |OVP_ENABLE_Pin 
                    #endif
                    |LVP_ENABLE_Pin|LED_FUNCTION_Pin|LED_ERROR_Pin, GPIO_PIN_RESET);

  //HAL_GPIO_WritePin(GPIOB, ADC_POWER_DOWN_Pin, GPIO_PIN_RESET);

  /*Configure GPIO pin Output Level */
  HAL_GPIO_WritePin(AUX_EN_GPIO_Port, AUX_EN_Pin, GPIO_PIN_RESET);

  /*Configure GPIO pin : PtPin */
  GPIO_InitStruct.Pin = ADC_DATA_READY_Pin;
  GPIO_InitStruct.Mode = GPIO_MODE_IT_FALLING;
  GPIO_InitStruct.Pull = GPIO_PULLUP;
  HAL_GPIO_Init(ADC_DATA_READY_GPIO_Port, &GPIO_InitStruct);



  /*Configure GPIO pins : PAPin PAPin PAPin PAPin 
                           PAPin PAPin PAPin PAPin 
                           PAPin */
  GPIO_InitStruct.Pin = ADC_RESET_Pin|ADC_START_CONV_Pin
                        #ifndef MCO_TEST_FUNCTION 
                        |OVP_ENABLE_Pin 
                        #endif
                        |LVP_ENABLE_Pin|LED_FUNCTION_Pin|LED_ERROR_Pin ;
  GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
  GPIO_InitStruct.Pull = GPIO_NOPULL;
  GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
  HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);


  /*Configure GPIO pin : PtPin */
  GPIO_InitStruct.Pin = BUTTON_Pin;
  GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
  GPIO_InitStruct.Pull = GPIO_PULLUP;
  HAL_GPIO_Init(BUTTON_GPIO_Port, &GPIO_InitStruct);

  /*Configure GPIO pin : PtPin */
  GPIO_InitStruct.Pin = AUX_EN_Pin;
  GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
  GPIO_InitStruct.Pull = GPIO_NOPULL;
  GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
  HAL_GPIO_Init(AUX_EN_GPIO_Port, &GPIO_InitStruct);

  // EDIT ECS
    // Reservierter Pin wird zu restore Factory beim Startup
    // Funktion wenn ber Jumper auf Masse gesetzt
  //GPIO_InitStruct.Pin = RESERVED_1_Pin;
  //GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
  //GPIO_InitStruct.Pull = GPIO_PULLUP;
  //GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
  //HAL_GPIO_Init(RESERVED_1_GPIO_Port, &GPIO_InitStruct);

  //GPIO_InitStruct.Pin = ADC_POWER_DOWN_Pin;
  //GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
  //GPIO_InitStruct.Pull = GPIO_PULLUP;
  //GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
  //HAL_GPIO_Init(ADC_POWER_DOWN_GPIO_Port, &GPIO_InitStruct);

  GPIO_InitStruct.Pin = ADC_RESET_Pin;
  GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
  GPIO_InitStruct.Pull = GPIO_PULLUP;
  GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
  HAL_GPIO_Init(ADC_RESET_GPIO_Port, &GPIO_InitStruct);
}

/* USER CODE BEGIN 2 */
void HAL_GPIO_EXTI_Falling_Callback(uint16_t GPIO_Pin)
{
  if (GPIO_Pin == ADC_DATA_READY_Pin)
  {
    newCurrentValue=1;

     
  }
}
/* USER CODE END 2 */

/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/