source: trunk/firmware/firmware.ioc

Last change on this file was 6, checked in by f.jahn, 3 months ago
File size: 11.3 KB
RevLine 
[6]1#MicroXplorer Configuration settings - do not modify
2Mcu.Family=STM32G0
3ProjectManager.MainLocation=Src
4PA6.Mode=Full_Duplex_Master
5RCC.USART1Freq_Value=16000000
6RCC.CortexFreq_Value=16000000
7ProjectManager.KeepUserCode=true
8Mcu.UserName=STM32G070KBTx
9SPI1.VirtualType=VM_MASTER
10ADC1.Overrun=ADC_OVR_DATA_OVERWRITTEN
11VP_ADC1_TempSens_Input.Mode=IN-TempSens
12ADC1.ContinuousConvMode=ENABLE
13Dma.ADC1.0.Polarity=HAL_DMAMUX_REQ_GEN_RISING
14SH.GPXTI9.0=GPIO_EXTI9
15PA11\ [PA9].GPIO_Label=LED_ERROR
16PA12\ [PA10].GPIO_Label=RESERVED_1
17USART1.WordLength=WORDLENGTH_9B
18PA0.GPIO_Label=AIN_U_SHUNT
19PA14-BOOT0.Mode=Serial_Wire
20ProjectManager.functionlistsort=1-MX_GPIO_Init-GPIO-false-HAL-true,2-MX_DMA_Init-DMA-false-HAL-true,3-MX_SPI1_Init-SPI1-false-HAL-true,4-MX_USART1_UART_Init-USART1-false-HAL-true,5-MX_ADC1_Init-ADC1-false-HAL-true,6-MX_RTC_Init-RTC-false-HAL-true,7-SystemClock_Config-RCC-false-HAL-false
21PA9.GPIOParameters=GPIO_Label
22PC6.GPIO_Label=FACTORY
23VP_RTC_VS_RTC_Activate.Mode=RTC_Enabled
24RCC.RTCFreq_Value=32768
25PA6.GPIO_Label=ADC_SPI1_MISO
26PB0.GPIO_Label=AIN_VREF_MEAS
27PB6.GPIO_Label=RS485_R
28RCC.USART2Freq_Value=16000000
29PC15-OSC32_OUT\ (PC15).Mode=LSE-External-Oscillator
30ADC1.SamplingTimeCommon2=ADC_SAMPLETIME_39CYCLES_5
31NVIC.SVC_IRQn=true\:0\:0\:false\:false\:true\:false\:false
32ADC1.SamplingTimeCommon1=ADC_SAMPLETIME_39CYCLES_5
33USART1.IPParameters=VirtualMode-Asynchronous,WordLength,Parity,VirtualMode-Hardware Flow Control (RS485)
34ADC1.SamplingTime-12\#ChannelRegularConversion=ADC_SAMPLINGTIME_COMMON_1
35PinOutPanel.RotationAngle=90
36RCC.MCO1PinFreq_Value=16000000
37ProjectManager.StackSize=0x400
38PB5.GPIOParameters=GPIO_Label
39PC14-OSC32_IN\ (PC14).Mode=LSE-External-Oscillator
40Mcu.IP4=RTC
41RCC.FCLKCortexFreq_Value=16000000
42Mcu.IP5=SPI1
43Mcu.IP2=NVIC
44Mcu.IP3=RCC
45PA15.GPIO_Label=RESERVED_2
46PB4.GPIOParameters=GPIO_Label
47Mcu.IP0=ADC1
48Mcu.IP1=DMA
49Mcu.UserConstants=
50PA4.Mode=IN4
51Mcu.ThirdPartyNb=0
52ADC1.Rank-11\#ChannelRegularConversion=2
53SPI1.Direction=SPI_DIRECTION_2LINES
54RCC.HCLKFreq_Value=16000000
55PA12\ [PA10].Signal=GPIO_Output
56Mcu.IPNb=8
57ProjectManager.PreviousToolchain=TrueSTUDIO
58SH.SharedAnalog_PB2.ConfNb=2
59PB6.Signal=USART1_TX
60Dma.ADC1.0.Direction=DMA_PERIPH_TO_MEMORY
61PB6.Mode=Asynchronous
62SPI1.CalculateBaudRate=4.0 MBits/s
63PA8.GPIOParameters=GPIO_Label
64PB9.GPIO_ModeDefaultEXTI=GPIO_MODE_IT_FALLING
65Mcu.Pin6=PA3
66Mcu.Pin7=PA4
67Mcu.Pin8=PA5
68Mcu.Pin9=PA6
69Dma.ADC1.0.MemDataAlignment=DMA_MDATAALIGN_WORD
70RCC.AHBFreq_Value=16000000
71Mcu.Pin0=PB9
72Mcu.Pin1=PC14-OSC32_IN (PC14)
73PA14-BOOT0.Signal=SYS_SWCLK
74GPIO.groupedBy=Group By Peripherals
75Mcu.Pin2=PC15-OSC32_OUT (PC15)
76Mcu.Pin3=PA0
77Mcu.Pin4=PA1
78Mcu.Pin5=PA2
79ProjectManager.ProjectBuild=false
80RCC.HSE_VALUE=8000000
81PA0.Locked=true
82PA11\ [PA9].GPIOParameters=GPIO_Label
83PB2.Signal=SharedAnalog_PB2
84PB3.Mode=Hardware Flow Control (RS485)
85PA8.Locked=true
86PA4.Locked=true
87NVIC.SysTick_IRQn=true\:0\:0\:false\:false\:true\:false\:true
88RCC.RTCClockSelection=RCC_RTCCLKSOURCE_LSE
89PA12\ [PA10].GPIOParameters=GPIO_Label
90ProjectManager.FirmwarePackage=STM32Cube FW_G0 V1.4.1
91VP_ADC1_Vref_Input.Mode=IN-Vrefint
92MxDb.Version=DB.6.0.10
93PB0.GPIOParameters=GPIO_Label
94ProjectManager.BackupPrevious=false
95RCC.VCOInputFreq_Value=16000000
96PB1.GPIO_Label=AIN_UB_MEAS
97Dma.ADC1.0.PeriphInc=DMA_PINC_DISABLE
98SPI1.DataSize=SPI_DATASIZE_8BIT
99File.Version=6
100PA10.GPIO_Label=LED_FUNCTION
101PA0.Mode=IN0
102VP_SYS_VS_DBSignals.Mode=DisableDeadBatterySignals
103PB7.Signal=USART1_RX
104PA8.Signal=GPIO_Output
105PB8.Locked=true
106RCC.PLLRCLKFreq_Value=64000000
107SPI1.VirtualNSS=VM_NSSHARD
108SH.SharedAnalog_PB0.0=GPIO_Analog
109PB6.Locked=true
110NVIC.PendSV_IRQn=true\:0\:0\:false\:false\:true\:false\:false
111Dma.RequestsNb=1
112PB6.GPIOParameters=GPIO_PuPd,GPIO_Label
113ProjectManager.HalAssertFull=false
114PB0.Locked=true
115ProjectManager.ProjectName=firmware
116PA0.Signal=ADC1_IN0
117PB7.GPIO_Label=RS485_D
118ADC1.SelectedChannel=ADC_CHANNEL_0|ADC_CHANNEL_1|ADC_CHANNEL_2|ADC_CHANNEL_3|ADC_CHANNEL_4|ADC_CHANNEL_8|ADC_CHANNEL_9|ADC_CHANNEL_10|ADC_CHANNEL_TEMPSENSOR|ADC_CHANNEL_VREFINT
119SH.SharedAnalog_PB0.1=ADC1_IN8,IN8
120Mcu.Package=LQFP32
121PB9.Signal=GPXTI9
122ADC1.SamplingTime-11\#ChannelRegularConversion=ADC_SAMPLINGTIME_COMMON_1
123PB1.Signal=SharedAnalog_PB1
124PA6.Signal=SPI1_MISO
125PA7.Locked=true
126PA5.Locked=true
127ADC1.OversamplingMode=DISABLE
128RCC.APBFreq_Value=16000000
129ADC1.SamplingTime-13\#ChannelRegularConversion=ADC_SAMPLINGTIME_COMMON_1
130ProjectManager.ToolChainLocation=
131RCC.LSI_VALUE=32000
132VP_SYS_VS_Systick.Signal=SYS_VS_Systick
133ADC1.Channel-11\#ChannelRegularConversion=ADC_CHANNEL_8
134RCC.LSCOPinFreq_Value=32000
135PB9.GPIO_PuPd=GPIO_PULLUP
136PA10.Signal=GPIO_Output
137PA15.Signal=GPIO_Output
138PA5.GPIOParameters=GPIO_Label
139PA12\ [PA10].Locked=true
140PC14-OSC32_IN\ (PC14).Locked=true
141PB5.GPIO_Label=ADC_RESET
142RCC.PLLPoutputFreq_Value=64000000
143SH.SharedAnalog_PB0.ConfNb=2
144NVIC.USART1_IRQn=true\:0\:0\:false\:false\:true\:true\:true
145Dma.Request0=ADC1
146SPI1.BaudRatePrescaler=SPI_BAUDRATEPRESCALER_4
147ADC1.EOCSelection=ADC_EOC_SEQ_CONV
148ProjectManager.CustomerFirmwarePackage=
149Dma.ADC1.0.EventEnable=DISABLE
150PB4.Signal=GPIO_Output
151PA3.Signal=ADC1_IN3
152PA5.Mode=Full_Duplex_Master
153VP_RTC_VS_RTC_Activate.Signal=RTC_VS_RTC_Activate
154PA6.GPIOParameters=GPIO_Label
155ADC1.Channel-10\#ChannelRegularConversion=ADC_CHANNEL_0
156ProjectManager.ProjectFileName=firmware.ioc
157Dma.ADC1.0.Instance=DMA1_Channel1
158PB8.GPIOParameters=GPIO_Label
159PA7.Mode=Full_Duplex_Master
160ADC1.Sequencer=FULLY_CONFIGURABLE
161PB9.GPIO_Label=ADC_DATA_READY
162PA15.GPIOParameters=GPIO_Label
163Mcu.PinsNb=34
164ADC1.Rank-10\#ChannelRegularConversion=1
165ProjectManager.NoMain=false
166SPI1.IPParameters=VirtualType,Mode,Direction,CalculateBaudRate,DataSize,BaudRatePrescaler,CLKPhase,VirtualNSS
167Dma.ADC1.0.SyncRequestNumber=1
168ADC1.IPParameters=NbrOfConversionFlag,SamplingTimeCommon1,ClockPrescaler,Sequencer,ContinuousConvMode,EOCSelection,Overrun,DMAContinuousRequests,OversamplingMode,TriggerFrequencyMode,Rank-10\#ChannelRegularConversion,Channel-10\#ChannelRegularConversion,SamplingTime-10\#ChannelRegularConversion,Rank-11\#ChannelRegularConversion,Channel-11\#ChannelRegularConversion,SamplingTime-11\#ChannelRegularConversion,Rank-12\#ChannelRegularConversion,Channel-12\#ChannelRegularConversion,SamplingTime-12\#ChannelRegularConversion,Rank-13\#ChannelRegularConversion,Channel-13\#ChannelRegularConversion,SamplingTime-13\#ChannelRegularConversion,NbrOfConversion,SamplingTimeCommon2,master,SelectedChannel,ChannelTS,ChannelVREF
169ADC1.ChannelVREF=ADC_CHANNEL_VREFINT
170PA9.GPIO_Label=LVP_ENABLE
171PB6.GPIO_PuPd=GPIO_PULLUP
172PC6.Signal=GPIO_Input
173RCC.EXTERNAL_CLOCK_VALUE=48000
174ProjectManager.DefaultFWLocation=true
175PC15-OSC32_OUT\ (PC15).Signal=RCC_OSC32_OUT
176SH.SharedAnalog_PB1.ConfNb=2
177SPI1.CLKPhase=SPI_PHASE_2EDGE
178ProjectManager.DeletePrevious=true
179ADC1.Channel-13\#ChannelRegularConversion=ADC_CHANNEL_VREFINT
180SH.SharedAnalog_PB2.1=ADC1_IN10,IN10
181SH.SharedAnalog_PB2.0=GPIO_Analog
182RCC.FamilyName=M
183PB9.GPIOParameters=GPIO_PuPd,GPIO_Label,GPIO_ModeDefaultEXTI
184USART1.VirtualMode-Asynchronous=VM_ASYNC
185PA3.Mode=IN3
186PA13.Signal=SYS_SWDIO
187ADC1.Rank-13\#ChannelRegularConversion=4
188PB8.GPIO_Label=VDDA3_SD
189Dma.ADC1.0.PeriphDataAlignment=DMA_PDATAALIGN_HALFWORD
190PA15.Locked=true
191PA8.GPIO_Label=OVP_ENABLE
192ProjectManager.TargetToolchain=TrueSTUDIO
193Dma.ADC1.0.Mode=DMA_CIRCULAR
194PB7.GPIOParameters=GPIO_Label
195Dma.ADC1.0.SignalID=NONE
196Dma.ADC1.0.SyncSignalID=NONE
197PC6.Locked=true
198Dma.ADC1.0.Priority=DMA_PRIORITY_LOW
199PB2.GPIOParameters=GPIO_Label
200PA9.Signal=GPIO_Output
201USART1.Parity=PARITY_EVEN
202RCC.I2S1Freq_Value=16000000
203PB9.Locked=true
204PB5.Locked=true
205ProjectManager.RegisterCallBack=
206PC15-OSC32_OUT\ (PC15).Locked=true
207PA11\ [PA9].Locked=true
208PA1.Signal=ADC1_IN1
209PB1.Locked=true
210PA5.Signal=SPI1_SCK
211SH.SharedAnalog_PB1.0=GPIO_Analog
212SH.SharedAnalog_PB1.1=ADC1_IN9,IN9
213board=custom
214ADC1.Rank-12\#ChannelRegularConversion=3
215RCC.VCOOutputFreq_Value=128000000
216ADC1.ChannelTS=ADC_CHANNEL_TEMPSENSOR
217ProjectManager.LastFirmware=true
218Dma.ADC1.0.SyncPolarity=HAL_DMAMUX_SYNC_NO_EVENT
219Dma.ADC1.0.RequestParameters=Instance,Direction,PeriphInc,MemInc,PeriphDataAlignment,MemDataAlignment,Mode,Priority,SignalID,Polarity,RequestNumber,SyncSignalID,SyncPolarity,SyncEnable,EventEnable,SyncRequestNumber
220ADC1.Channel-12\#ChannelRegularConversion=ADC_CHANNEL_TEMPSENSOR
221PA1.Mode=IN1
222MxCube.Version=6.1.1
223PB4.GPIO_Label=ADC_PWDN
224RCC.I2C1Freq_Value=16000000
225SPI1.Mode=SPI_MODE_MASTER
226VP_SYS_VS_DBSignals.Signal=SYS_VS_DBSignals
227VP_ADC1_TempSens_Input.Signal=ADC1_TempSens_Input
228USART1.VirtualMode-Hardware\ Flow\ Control\ (RS485)=VM_ASYNC
229Mcu.Pin30=VP_ADC1_Vref_Input
230RCC.ADCFreq_Value=16000000
231PA10.GPIOParameters=GPIO_Label
232VP_SYS_VS_Systick.Mode=SysTick
233VP_ADC1_Vref_Input.Signal=ADC1_Vref_Input
234Mcu.Pin33=VP_SYS_VS_DBSignals
235Mcu.Pin31=VP_RTC_VS_RTC_Activate
236Mcu.Pin32=VP_SYS_VS_Systick
237PA9.Locked=true
238NVIC.NonMaskableInt_IRQn=true\:0\:0\:false\:false\:true\:false\:false
239ADC1.DMAContinuousRequests=ENABLE
240ADC1.SamplingTime-10\#ChannelRegularConversion=ADC_SAMPLINGTIME_COMMON_1
241ADC1.NbrOfConversion=4
242PA13.Mode=Serial_Wire
243ProjectManager.FreePins=false
244RCC.IPParameters=ADCFreq_Value,AHBFreq_Value,APBFreq_Value,APBTimFreq_Value,CortexFreq_Value,EXTERNAL_CLOCK_VALUE,FCLKCortexFreq_Value,FamilyName,HCLKFreq_Value,HSE_VALUE,HSI_VALUE,I2C1Freq_Value,I2S1Freq_Value,LSCOPinFreq_Value,LSI_VALUE,MCO1PinFreq_Value,PLLPoutputFreq_Value,PLLRCLKFreq_Value,PWRFreq_Value,RTCClockSelection,RTCFreq_Value,SYSCLKFreq_VALUE,USART1Freq_Value,USART2Freq_Value,VCOInputFreq_Value,VCOOutputFreq_Value
245ProjectManager.AskForMigrate=true
246Mcu.Name=STM32G070KBTx
247PA11\ [PA9].Signal=GPIO_Output
248PA14-BOOT0.Locked=true
249Mcu.Pin26=PB6
250Mcu.Pin27=PB7
251PA2.Signal=ADC1_IN2
252Mcu.Pin24=PB4
253ProjectManager.UnderRoot=true
254Mcu.Pin25=PB5
255PB2.Locked=true
256Mcu.Pin28=PB8
257Mcu.IP6=SYS
258Mcu.Pin29=VP_ADC1_TempSens_Input
259Mcu.IP7=USART1
260ProjectManager.CoupleFile=true
261PB4.Locked=true
262PB3.Signal=USART1_DE
263PA4.Signal=ADC1_IN4
264RCC.APBTimFreq_Value=16000000
265RCC.SYSCLKFreq_VALUE=16000000
266Mcu.Pin22=PA15
267PB5.Signal=GPIO_Output
268Mcu.Pin23=PB3
269PA7.GPIO_Label=ADC_SPI1_MOSI
270Mcu.Pin20=PA13
271ADC1.master=1
272PA3.Locked=true
273Mcu.Pin21=PA14-BOOT0
274PA10.Locked=true
275PA5.GPIO_Label=ADC_SPI1_SCK
276NVIC.ForceEnableDMAVector=true
277KeepUserPlacement=false
278ADC1.TriggerFrequencyMode=ADC_TRIGGER_FREQ_HIGH
279PC14-OSC32_IN\ (PC14).Signal=RCC_OSC32_IN
280PA13.Locked=true
281ProjectManager.CompilerOptimize=6
282Dma.ADC1.0.RequestNumber=1
283PB7.Mode=Asynchronous
284SH.GPXTI9.ConfNb=1
285Dma.ADC1.0.SyncEnable=DISABLE
286Dma.ADC1.0.MemInc=DMA_MINC_ENABLE
287PB2.GPIO_Label=AIN_TEMP_MEAS
288ProjectManager.HeapSize=0x200
289PA0.GPIOParameters=GPIO_Label
290Mcu.Pin15=PA9
291NVIC.HardFault_IRQn=true\:0\:0\:false\:false\:true\:false\:false
292Mcu.Pin16=PC6
293Mcu.Pin13=PB2
294Mcu.Pin14=PA8
295PC6.GPIOParameters=GPIO_Label
296Mcu.Pin19=PA12 [PA10]
297ProjectManager.ComputerToolchain=false
298Mcu.Pin17=PA10
299RCC.HSI_VALUE=16000000
300Mcu.Pin18=PA11 [PA9]
301ADC1.NbrOfConversionFlag=1
302Mcu.Pin11=PB0
303Mcu.Pin12=PB1
304Mcu.Pin10=PA7
305PB7.Locked=true
306PA2.Mode=IN2
307PB8.Signal=GPIO_Output
308RCC.PWRFreq_Value=16000000
309NVIC.DMA1_Channel1_IRQn=true\:1\:0\:true\:false\:true\:false\:true
310PB0.Signal=SharedAnalog_PB0
311ADC1.ClockPrescaler=ADC_CLOCK_ASYNC_DIV16
312PA7.GPIOParameters=GPIO_Label
313ProjectManager.DeviceId=STM32G070KBTx
314ProjectManager.LibraryCopy=1
315PB1.GPIOParameters=GPIO_Label
316PA7.Signal=SPI1_MOSI
317PA6.Locked=true
Note: See TracBrowser for help on using the repository browser.