| 1 | #MicroXplorer Configuration settings - do not modify |
|---|
| 2 | Mcu.Family=STM32G0 |
|---|
| 3 | ProjectManager.MainLocation=Src |
|---|
| 4 | PA6.Mode=Full_Duplex_Master |
|---|
| 5 | RCC.USART1Freq_Value=16000000 |
|---|
| 6 | RCC.CortexFreq_Value=16000000 |
|---|
| 7 | ProjectManager.KeepUserCode=true |
|---|
| 8 | Mcu.UserName=STM32G070KBTx |
|---|
| 9 | SPI1.VirtualType=VM_MASTER |
|---|
| 10 | ADC1.Overrun=ADC_OVR_DATA_OVERWRITTEN |
|---|
| 11 | VP_ADC1_TempSens_Input.Mode=IN-TempSens |
|---|
| 12 | ADC1.ContinuousConvMode=ENABLE |
|---|
| 13 | Dma.ADC1.0.Polarity=HAL_DMAMUX_REQ_GEN_RISING |
|---|
| 14 | SH.GPXTI9.0=GPIO_EXTI9 |
|---|
| 15 | PA11\ [PA9].GPIO_Label=LED_ERROR |
|---|
| 16 | PA12\ [PA10].GPIO_Label=RESERVED_1 |
|---|
| 17 | USART1.WordLength=WORDLENGTH_9B |
|---|
| 18 | PA0.GPIO_Label=AIN_U_SHUNT |
|---|
| 19 | PA14-BOOT0.Mode=Serial_Wire |
|---|
| 20 | ProjectManager.functionlistsort=1-MX_GPIO_Init-GPIO-false-HAL-true,2-MX_DMA_Init-DMA-false-HAL-true,3-MX_SPI1_Init-SPI1-false-HAL-true,4-MX_USART1_UART_Init-USART1-false-HAL-true,5-MX_ADC1_Init-ADC1-false-HAL-true,6-MX_RTC_Init-RTC-false-HAL-true,7-SystemClock_Config-RCC-false-HAL-false |
|---|
| 21 | PA9.GPIOParameters=GPIO_Label |
|---|
| 22 | PC6.GPIO_Label=FACTORY |
|---|
| 23 | VP_RTC_VS_RTC_Activate.Mode=RTC_Enabled |
|---|
| 24 | RCC.RTCFreq_Value=32768 |
|---|
| 25 | PA6.GPIO_Label=ADC_SPI1_MISO |
|---|
| 26 | PB0.GPIO_Label=AIN_VREF_MEAS |
|---|
| 27 | PB6.GPIO_Label=RS485_R |
|---|
| 28 | RCC.USART2Freq_Value=16000000 |
|---|
| 29 | PC15-OSC32_OUT\ (PC15).Mode=LSE-External-Oscillator |
|---|
| 30 | ADC1.SamplingTimeCommon2=ADC_SAMPLETIME_39CYCLES_5 |
|---|
| 31 | NVIC.SVC_IRQn=true\:0\:0\:false\:false\:true\:false\:false |
|---|
| 32 | ADC1.SamplingTimeCommon1=ADC_SAMPLETIME_39CYCLES_5 |
|---|
| 33 | USART1.IPParameters=VirtualMode-Asynchronous,WordLength,Parity,VirtualMode-Hardware Flow Control (RS485) |
|---|
| 34 | ADC1.SamplingTime-12\#ChannelRegularConversion=ADC_SAMPLINGTIME_COMMON_1 |
|---|
| 35 | PinOutPanel.RotationAngle=90 |
|---|
| 36 | RCC.MCO1PinFreq_Value=16000000 |
|---|
| 37 | ProjectManager.StackSize=0x400 |
|---|
| 38 | PB5.GPIOParameters=GPIO_Label |
|---|
| 39 | PC14-OSC32_IN\ (PC14).Mode=LSE-External-Oscillator |
|---|
| 40 | Mcu.IP4=RTC |
|---|
| 41 | RCC.FCLKCortexFreq_Value=16000000 |
|---|
| 42 | Mcu.IP5=SPI1 |
|---|
| 43 | Mcu.IP2=NVIC |
|---|
| 44 | Mcu.IP3=RCC |
|---|
| 45 | PA15.GPIO_Label=RESERVED_2 |
|---|
| 46 | PB4.GPIOParameters=GPIO_Label |
|---|
| 47 | Mcu.IP0=ADC1 |
|---|
| 48 | Mcu.IP1=DMA |
|---|
| 49 | Mcu.UserConstants= |
|---|
| 50 | PA4.Mode=IN4 |
|---|
| 51 | Mcu.ThirdPartyNb=0 |
|---|
| 52 | ADC1.Rank-11\#ChannelRegularConversion=2 |
|---|
| 53 | SPI1.Direction=SPI_DIRECTION_2LINES |
|---|
| 54 | RCC.HCLKFreq_Value=16000000 |
|---|
| 55 | PA12\ [PA10].Signal=GPIO_Output |
|---|
| 56 | Mcu.IPNb=8 |
|---|
| 57 | ProjectManager.PreviousToolchain=TrueSTUDIO |
|---|
| 58 | SH.SharedAnalog_PB2.ConfNb=2 |
|---|
| 59 | PB6.Signal=USART1_TX |
|---|
| 60 | Dma.ADC1.0.Direction=DMA_PERIPH_TO_MEMORY |
|---|
| 61 | PB6.Mode=Asynchronous |
|---|
| 62 | SPI1.CalculateBaudRate=4.0 MBits/s |
|---|
| 63 | PA8.GPIOParameters=GPIO_Label |
|---|
| 64 | PB9.GPIO_ModeDefaultEXTI=GPIO_MODE_IT_FALLING |
|---|
| 65 | Mcu.Pin6=PA3 |
|---|
| 66 | Mcu.Pin7=PA4 |
|---|
| 67 | Mcu.Pin8=PA5 |
|---|
| 68 | Mcu.Pin9=PA6 |
|---|
| 69 | Dma.ADC1.0.MemDataAlignment=DMA_MDATAALIGN_WORD |
|---|
| 70 | RCC.AHBFreq_Value=16000000 |
|---|
| 71 | Mcu.Pin0=PB9 |
|---|
| 72 | Mcu.Pin1=PC14-OSC32_IN (PC14) |
|---|
| 73 | PA14-BOOT0.Signal=SYS_SWCLK |
|---|
| 74 | GPIO.groupedBy=Group By Peripherals |
|---|
| 75 | Mcu.Pin2=PC15-OSC32_OUT (PC15) |
|---|
| 76 | Mcu.Pin3=PA0 |
|---|
| 77 | Mcu.Pin4=PA1 |
|---|
| 78 | Mcu.Pin5=PA2 |
|---|
| 79 | ProjectManager.ProjectBuild=false |
|---|
| 80 | RCC.HSE_VALUE=8000000 |
|---|
| 81 | PA0.Locked=true |
|---|
| 82 | PA11\ [PA9].GPIOParameters=GPIO_Label |
|---|
| 83 | PB2.Signal=SharedAnalog_PB2 |
|---|
| 84 | PB3.Mode=Hardware Flow Control (RS485) |
|---|
| 85 | PA8.Locked=true |
|---|
| 86 | PA4.Locked=true |
|---|
| 87 | NVIC.SysTick_IRQn=true\:0\:0\:false\:false\:true\:false\:true |
|---|
| 88 | RCC.RTCClockSelection=RCC_RTCCLKSOURCE_LSE |
|---|
| 89 | PA12\ [PA10].GPIOParameters=GPIO_Label |
|---|
| 90 | ProjectManager.FirmwarePackage=STM32Cube FW_G0 V1.4.1 |
|---|
| 91 | VP_ADC1_Vref_Input.Mode=IN-Vrefint |
|---|
| 92 | MxDb.Version=DB.6.0.10 |
|---|
| 93 | PB0.GPIOParameters=GPIO_Label |
|---|
| 94 | ProjectManager.BackupPrevious=false |
|---|
| 95 | RCC.VCOInputFreq_Value=16000000 |
|---|
| 96 | PB1.GPIO_Label=AIN_UB_MEAS |
|---|
| 97 | Dma.ADC1.0.PeriphInc=DMA_PINC_DISABLE |
|---|
| 98 | SPI1.DataSize=SPI_DATASIZE_8BIT |
|---|
| 99 | File.Version=6 |
|---|
| 100 | PA10.GPIO_Label=LED_FUNCTION |
|---|
| 101 | PA0.Mode=IN0 |
|---|
| 102 | VP_SYS_VS_DBSignals.Mode=DisableDeadBatterySignals |
|---|
| 103 | PB7.Signal=USART1_RX |
|---|
| 104 | PA8.Signal=GPIO_Output |
|---|
| 105 | PB8.Locked=true |
|---|
| 106 | RCC.PLLRCLKFreq_Value=64000000 |
|---|
| 107 | SPI1.VirtualNSS=VM_NSSHARD |
|---|
| 108 | SH.SharedAnalog_PB0.0=GPIO_Analog |
|---|
| 109 | PB6.Locked=true |
|---|
| 110 | NVIC.PendSV_IRQn=true\:0\:0\:false\:false\:true\:false\:false |
|---|
| 111 | Dma.RequestsNb=1 |
|---|
| 112 | PB6.GPIOParameters=GPIO_PuPd,GPIO_Label |
|---|
| 113 | ProjectManager.HalAssertFull=false |
|---|
| 114 | PB0.Locked=true |
|---|
| 115 | ProjectManager.ProjectName=firmware |
|---|
| 116 | PA0.Signal=ADC1_IN0 |
|---|
| 117 | PB7.GPIO_Label=RS485_D |
|---|
| 118 | ADC1.SelectedChannel=ADC_CHANNEL_0|ADC_CHANNEL_1|ADC_CHANNEL_2|ADC_CHANNEL_3|ADC_CHANNEL_4|ADC_CHANNEL_8|ADC_CHANNEL_9|ADC_CHANNEL_10|ADC_CHANNEL_TEMPSENSOR|ADC_CHANNEL_VREFINT |
|---|
| 119 | SH.SharedAnalog_PB0.1=ADC1_IN8,IN8 |
|---|
| 120 | Mcu.Package=LQFP32 |
|---|
| 121 | PB9.Signal=GPXTI9 |
|---|
| 122 | ADC1.SamplingTime-11\#ChannelRegularConversion=ADC_SAMPLINGTIME_COMMON_1 |
|---|
| 123 | PB1.Signal=SharedAnalog_PB1 |
|---|
| 124 | PA6.Signal=SPI1_MISO |
|---|
| 125 | PA7.Locked=true |
|---|
| 126 | PA5.Locked=true |
|---|
| 127 | ADC1.OversamplingMode=DISABLE |
|---|
| 128 | RCC.APBFreq_Value=16000000 |
|---|
| 129 | ADC1.SamplingTime-13\#ChannelRegularConversion=ADC_SAMPLINGTIME_COMMON_1 |
|---|
| 130 | ProjectManager.ToolChainLocation= |
|---|
| 131 | RCC.LSI_VALUE=32000 |
|---|
| 132 | VP_SYS_VS_Systick.Signal=SYS_VS_Systick |
|---|
| 133 | ADC1.Channel-11\#ChannelRegularConversion=ADC_CHANNEL_8 |
|---|
| 134 | RCC.LSCOPinFreq_Value=32000 |
|---|
| 135 | PB9.GPIO_PuPd=GPIO_PULLUP |
|---|
| 136 | PA10.Signal=GPIO_Output |
|---|
| 137 | PA15.Signal=GPIO_Output |
|---|
| 138 | PA5.GPIOParameters=GPIO_Label |
|---|
| 139 | PA12\ [PA10].Locked=true |
|---|
| 140 | PC14-OSC32_IN\ (PC14).Locked=true |
|---|
| 141 | PB5.GPIO_Label=ADC_RESET |
|---|
| 142 | RCC.PLLPoutputFreq_Value=64000000 |
|---|
| 143 | SH.SharedAnalog_PB0.ConfNb=2 |
|---|
| 144 | NVIC.USART1_IRQn=true\:0\:0\:false\:false\:true\:true\:true |
|---|
| 145 | Dma.Request0=ADC1 |
|---|
| 146 | SPI1.BaudRatePrescaler=SPI_BAUDRATEPRESCALER_4 |
|---|
| 147 | ADC1.EOCSelection=ADC_EOC_SEQ_CONV |
|---|
| 148 | ProjectManager.CustomerFirmwarePackage= |
|---|
| 149 | Dma.ADC1.0.EventEnable=DISABLE |
|---|
| 150 | PB4.Signal=GPIO_Output |
|---|
| 151 | PA3.Signal=ADC1_IN3 |
|---|
| 152 | PA5.Mode=Full_Duplex_Master |
|---|
| 153 | VP_RTC_VS_RTC_Activate.Signal=RTC_VS_RTC_Activate |
|---|
| 154 | PA6.GPIOParameters=GPIO_Label |
|---|
| 155 | ADC1.Channel-10\#ChannelRegularConversion=ADC_CHANNEL_0 |
|---|
| 156 | ProjectManager.ProjectFileName=firmware.ioc |
|---|
| 157 | Dma.ADC1.0.Instance=DMA1_Channel1 |
|---|
| 158 | PB8.GPIOParameters=GPIO_Label |
|---|
| 159 | PA7.Mode=Full_Duplex_Master |
|---|
| 160 | ADC1.Sequencer=FULLY_CONFIGURABLE |
|---|
| 161 | PB9.GPIO_Label=ADC_DATA_READY |
|---|
| 162 | PA15.GPIOParameters=GPIO_Label |
|---|
| 163 | Mcu.PinsNb=34 |
|---|
| 164 | ADC1.Rank-10\#ChannelRegularConversion=1 |
|---|
| 165 | ProjectManager.NoMain=false |
|---|
| 166 | SPI1.IPParameters=VirtualType,Mode,Direction,CalculateBaudRate,DataSize,BaudRatePrescaler,CLKPhase,VirtualNSS |
|---|
| 167 | Dma.ADC1.0.SyncRequestNumber=1 |
|---|
| 168 | ADC1.IPParameters=NbrOfConversionFlag,SamplingTimeCommon1,ClockPrescaler,Sequencer,ContinuousConvMode,EOCSelection,Overrun,DMAContinuousRequests,OversamplingMode,TriggerFrequencyMode,Rank-10\#ChannelRegularConversion,Channel-10\#ChannelRegularConversion,SamplingTime-10\#ChannelRegularConversion,Rank-11\#ChannelRegularConversion,Channel-11\#ChannelRegularConversion,SamplingTime-11\#ChannelRegularConversion,Rank-12\#ChannelRegularConversion,Channel-12\#ChannelRegularConversion,SamplingTime-12\#ChannelRegularConversion,Rank-13\#ChannelRegularConversion,Channel-13\#ChannelRegularConversion,SamplingTime-13\#ChannelRegularConversion,NbrOfConversion,SamplingTimeCommon2,master,SelectedChannel,ChannelTS,ChannelVREF |
|---|
| 169 | ADC1.ChannelVREF=ADC_CHANNEL_VREFINT |
|---|
| 170 | PA9.GPIO_Label=LVP_ENABLE |
|---|
| 171 | PB6.GPIO_PuPd=GPIO_PULLUP |
|---|
| 172 | PC6.Signal=GPIO_Input |
|---|
| 173 | RCC.EXTERNAL_CLOCK_VALUE=48000 |
|---|
| 174 | ProjectManager.DefaultFWLocation=true |
|---|
| 175 | PC15-OSC32_OUT\ (PC15).Signal=RCC_OSC32_OUT |
|---|
| 176 | SH.SharedAnalog_PB1.ConfNb=2 |
|---|
| 177 | SPI1.CLKPhase=SPI_PHASE_2EDGE |
|---|
| 178 | ProjectManager.DeletePrevious=true |
|---|
| 179 | ADC1.Channel-13\#ChannelRegularConversion=ADC_CHANNEL_VREFINT |
|---|
| 180 | SH.SharedAnalog_PB2.1=ADC1_IN10,IN10 |
|---|
| 181 | SH.SharedAnalog_PB2.0=GPIO_Analog |
|---|
| 182 | RCC.FamilyName=M |
|---|
| 183 | PB9.GPIOParameters=GPIO_PuPd,GPIO_Label,GPIO_ModeDefaultEXTI |
|---|
| 184 | USART1.VirtualMode-Asynchronous=VM_ASYNC |
|---|
| 185 | PA3.Mode=IN3 |
|---|
| 186 | PA13.Signal=SYS_SWDIO |
|---|
| 187 | ADC1.Rank-13\#ChannelRegularConversion=4 |
|---|
| 188 | PB8.GPIO_Label=VDDA3_SD |
|---|
| 189 | Dma.ADC1.0.PeriphDataAlignment=DMA_PDATAALIGN_HALFWORD |
|---|
| 190 | PA15.Locked=true |
|---|
| 191 | PA8.GPIO_Label=OVP_ENABLE |
|---|
| 192 | ProjectManager.TargetToolchain=TrueSTUDIO |
|---|
| 193 | Dma.ADC1.0.Mode=DMA_CIRCULAR |
|---|
| 194 | PB7.GPIOParameters=GPIO_Label |
|---|
| 195 | Dma.ADC1.0.SignalID=NONE |
|---|
| 196 | Dma.ADC1.0.SyncSignalID=NONE |
|---|
| 197 | PC6.Locked=true |
|---|
| 198 | Dma.ADC1.0.Priority=DMA_PRIORITY_LOW |
|---|
| 199 | PB2.GPIOParameters=GPIO_Label |
|---|
| 200 | PA9.Signal=GPIO_Output |
|---|
| 201 | USART1.Parity=PARITY_EVEN |
|---|
| 202 | RCC.I2S1Freq_Value=16000000 |
|---|
| 203 | PB9.Locked=true |
|---|
| 204 | PB5.Locked=true |
|---|
| 205 | ProjectManager.RegisterCallBack= |
|---|
| 206 | PC15-OSC32_OUT\ (PC15).Locked=true |
|---|
| 207 | PA11\ [PA9].Locked=true |
|---|
| 208 | PA1.Signal=ADC1_IN1 |
|---|
| 209 | PB1.Locked=true |
|---|
| 210 | PA5.Signal=SPI1_SCK |
|---|
| 211 | SH.SharedAnalog_PB1.0=GPIO_Analog |
|---|
| 212 | SH.SharedAnalog_PB1.1=ADC1_IN9,IN9 |
|---|
| 213 | board=custom |
|---|
| 214 | ADC1.Rank-12\#ChannelRegularConversion=3 |
|---|
| 215 | RCC.VCOOutputFreq_Value=128000000 |
|---|
| 216 | ADC1.ChannelTS=ADC_CHANNEL_TEMPSENSOR |
|---|
| 217 | ProjectManager.LastFirmware=true |
|---|
| 218 | Dma.ADC1.0.SyncPolarity=HAL_DMAMUX_SYNC_NO_EVENT |
|---|
| 219 | Dma.ADC1.0.RequestParameters=Instance,Direction,PeriphInc,MemInc,PeriphDataAlignment,MemDataAlignment,Mode,Priority,SignalID,Polarity,RequestNumber,SyncSignalID,SyncPolarity,SyncEnable,EventEnable,SyncRequestNumber |
|---|
| 220 | ADC1.Channel-12\#ChannelRegularConversion=ADC_CHANNEL_TEMPSENSOR |
|---|
| 221 | PA1.Mode=IN1 |
|---|
| 222 | MxCube.Version=6.1.1 |
|---|
| 223 | PB4.GPIO_Label=ADC_PWDN |
|---|
| 224 | RCC.I2C1Freq_Value=16000000 |
|---|
| 225 | SPI1.Mode=SPI_MODE_MASTER |
|---|
| 226 | VP_SYS_VS_DBSignals.Signal=SYS_VS_DBSignals |
|---|
| 227 | VP_ADC1_TempSens_Input.Signal=ADC1_TempSens_Input |
|---|
| 228 | USART1.VirtualMode-Hardware\ Flow\ Control\ (RS485)=VM_ASYNC |
|---|
| 229 | Mcu.Pin30=VP_ADC1_Vref_Input |
|---|
| 230 | RCC.ADCFreq_Value=16000000 |
|---|
| 231 | PA10.GPIOParameters=GPIO_Label |
|---|
| 232 | VP_SYS_VS_Systick.Mode=SysTick |
|---|
| 233 | VP_ADC1_Vref_Input.Signal=ADC1_Vref_Input |
|---|
| 234 | Mcu.Pin33=VP_SYS_VS_DBSignals |
|---|
| 235 | Mcu.Pin31=VP_RTC_VS_RTC_Activate |
|---|
| 236 | Mcu.Pin32=VP_SYS_VS_Systick |
|---|
| 237 | PA9.Locked=true |
|---|
| 238 | NVIC.NonMaskableInt_IRQn=true\:0\:0\:false\:false\:true\:false\:false |
|---|
| 239 | ADC1.DMAContinuousRequests=ENABLE |
|---|
| 240 | ADC1.SamplingTime-10\#ChannelRegularConversion=ADC_SAMPLINGTIME_COMMON_1 |
|---|
| 241 | ADC1.NbrOfConversion=4 |
|---|
| 242 | PA13.Mode=Serial_Wire |
|---|
| 243 | ProjectManager.FreePins=false |
|---|
| 244 | RCC.IPParameters=ADCFreq_Value,AHBFreq_Value,APBFreq_Value,APBTimFreq_Value,CortexFreq_Value,EXTERNAL_CLOCK_VALUE,FCLKCortexFreq_Value,FamilyName,HCLKFreq_Value,HSE_VALUE,HSI_VALUE,I2C1Freq_Value,I2S1Freq_Value,LSCOPinFreq_Value,LSI_VALUE,MCO1PinFreq_Value,PLLPoutputFreq_Value,PLLRCLKFreq_Value,PWRFreq_Value,RTCClockSelection,RTCFreq_Value,SYSCLKFreq_VALUE,USART1Freq_Value,USART2Freq_Value,VCOInputFreq_Value,VCOOutputFreq_Value |
|---|
| 245 | ProjectManager.AskForMigrate=true |
|---|
| 246 | Mcu.Name=STM32G070KBTx |
|---|
| 247 | PA11\ [PA9].Signal=GPIO_Output |
|---|
| 248 | PA14-BOOT0.Locked=true |
|---|
| 249 | Mcu.Pin26=PB6 |
|---|
| 250 | Mcu.Pin27=PB7 |
|---|
| 251 | PA2.Signal=ADC1_IN2 |
|---|
| 252 | Mcu.Pin24=PB4 |
|---|
| 253 | ProjectManager.UnderRoot=true |
|---|
| 254 | Mcu.Pin25=PB5 |
|---|
| 255 | PB2.Locked=true |
|---|
| 256 | Mcu.Pin28=PB8 |
|---|
| 257 | Mcu.IP6=SYS |
|---|
| 258 | Mcu.Pin29=VP_ADC1_TempSens_Input |
|---|
| 259 | Mcu.IP7=USART1 |
|---|
| 260 | ProjectManager.CoupleFile=true |
|---|
| 261 | PB4.Locked=true |
|---|
| 262 | PB3.Signal=USART1_DE |
|---|
| 263 | PA4.Signal=ADC1_IN4 |
|---|
| 264 | RCC.APBTimFreq_Value=16000000 |
|---|
| 265 | RCC.SYSCLKFreq_VALUE=16000000 |
|---|
| 266 | Mcu.Pin22=PA15 |
|---|
| 267 | PB5.Signal=GPIO_Output |
|---|
| 268 | Mcu.Pin23=PB3 |
|---|
| 269 | PA7.GPIO_Label=ADC_SPI1_MOSI |
|---|
| 270 | Mcu.Pin20=PA13 |
|---|
| 271 | ADC1.master=1 |
|---|
| 272 | PA3.Locked=true |
|---|
| 273 | Mcu.Pin21=PA14-BOOT0 |
|---|
| 274 | PA10.Locked=true |
|---|
| 275 | PA5.GPIO_Label=ADC_SPI1_SCK |
|---|
| 276 | NVIC.ForceEnableDMAVector=true |
|---|
| 277 | KeepUserPlacement=false |
|---|
| 278 | ADC1.TriggerFrequencyMode=ADC_TRIGGER_FREQ_HIGH |
|---|
| 279 | PC14-OSC32_IN\ (PC14).Signal=RCC_OSC32_IN |
|---|
| 280 | PA13.Locked=true |
|---|
| 281 | ProjectManager.CompilerOptimize=6 |
|---|
| 282 | Dma.ADC1.0.RequestNumber=1 |
|---|
| 283 | PB7.Mode=Asynchronous |
|---|
| 284 | SH.GPXTI9.ConfNb=1 |
|---|
| 285 | Dma.ADC1.0.SyncEnable=DISABLE |
|---|
| 286 | Dma.ADC1.0.MemInc=DMA_MINC_ENABLE |
|---|
| 287 | PB2.GPIO_Label=AIN_TEMP_MEAS |
|---|
| 288 | ProjectManager.HeapSize=0x200 |
|---|
| 289 | PA0.GPIOParameters=GPIO_Label |
|---|
| 290 | Mcu.Pin15=PA9 |
|---|
| 291 | NVIC.HardFault_IRQn=true\:0\:0\:false\:false\:true\:false\:false |
|---|
| 292 | Mcu.Pin16=PC6 |
|---|
| 293 | Mcu.Pin13=PB2 |
|---|
| 294 | Mcu.Pin14=PA8 |
|---|
| 295 | PC6.GPIOParameters=GPIO_Label |
|---|
| 296 | Mcu.Pin19=PA12 [PA10] |
|---|
| 297 | ProjectManager.ComputerToolchain=false |
|---|
| 298 | Mcu.Pin17=PA10 |
|---|
| 299 | RCC.HSI_VALUE=16000000 |
|---|
| 300 | Mcu.Pin18=PA11 [PA9] |
|---|
| 301 | ADC1.NbrOfConversionFlag=1 |
|---|
| 302 | Mcu.Pin11=PB0 |
|---|
| 303 | Mcu.Pin12=PB1 |
|---|
| 304 | Mcu.Pin10=PA7 |
|---|
| 305 | PB7.Locked=true |
|---|
| 306 | PA2.Mode=IN2 |
|---|
| 307 | PB8.Signal=GPIO_Output |
|---|
| 308 | RCC.PWRFreq_Value=16000000 |
|---|
| 309 | NVIC.DMA1_Channel1_IRQn=true\:1\:0\:true\:false\:true\:false\:true |
|---|
| 310 | PB0.Signal=SharedAnalog_PB0 |
|---|
| 311 | ADC1.ClockPrescaler=ADC_CLOCK_ASYNC_DIV16 |
|---|
| 312 | PA7.GPIOParameters=GPIO_Label |
|---|
| 313 | ProjectManager.DeviceId=STM32G070KBTx |
|---|
| 314 | ProjectManager.LibraryCopy=1 |
|---|
| 315 | PB1.GPIOParameters=GPIO_Label |
|---|
| 316 | PA7.Signal=SPI1_MOSI |
|---|
| 317 | PA6.Locked=true |
|---|
